During my last trip to Raja Ampat I had finally the opportunity to take the wide angle lenses in a real life situation and test that they were working to satisfaction. As some people know I really like my set of Inon AD lenses and although the RX100 has a 28mm equivalent lens I put together a bespoke adapter to reuse the lenses I already have. At the time of the trip I did not have the final prototype but only a pre-release which meant I could no use the fisheye as I had an alignment issue with the dome so I only used the flat UWL105AD.
There are two videos that are of interest one is the Raja Ampat North sites which is below.
In the north visibility was at best fair and I was struggling with the set up as I had not tested the push up filter. What happened is that the black ring created vignetting so I had to reverse the rubber ring on the lens until I could push the filter deeper. In the video you can see clearly a vignetting issue around 3:50 on the wobbegong approach where I had not yet resolved this problem. The video has no image stabilization nor cropping and it shows! There are also occasional soft corners as due to the low level of visibility and lack of light the camera was working around f1.8 or f2.0 aperture most of the time. This does create soft corners on the RX100 when you have something in close focus because I always shoot at the lowest ISO as I have found that increasing aperture and working with high ISO creates a mayhem of chromatic issues.
Anyway once I got a few dives and the problems were ironed out we also moved down to Misool where conditions where much better. This is the Misool video.
Here because of the increase of light and better conditions the image is sharper due to smaller aperture settings. I did not use the RX100 to take any stills as I wanted to focus entirely on video.
Once I got home I bought a fix M67-28AD adapter PRO, that allows you to adjust the AD lens so that the dome petals are in the right place. I tested it in the bathtub with the UFL165AD and the UWL105AD, in terms of vignetting as we shoot stills at 3:2 the working focal length is 34mm on the zoom or 12.8mm.
This is a shot of the bare lens
You can see the characteristic pincushion distortion that the bare port creates, this is the main reason together to demagnification to have a wet wide angle lens note the purple fringing is evident.
This is a shot at f5.6 with the UFL165AD.
Despite the zoom the lens performs great and it is very wide. If we look at a 100% zoom of the corner
We can see that at this aperture the corners are sharp and there is a very small amount of red and blue fringing.
Let’s look at the Inon UWL105AD
If we zoom into the corner this is what we get
Also here there is tiny blue and yellow fringing but the results are comparable to some shots I have been sent taken with the Inon UWLH-100 28LD.
Finally this is the UWL105AD with a 16:9 aspect ratio and 33mm equivalent zoom, this is interesting as it is the way the camera behaves in active steady shot without zoom.
As you can see even better performance in the corners as the port is closer to the back of the lens with the RX100 because of how zooming is implemented.
For who is interested I sell spacer rings and special screws that you can attach to the fix adapter at $45 get in touch if you have some old AD lenses and you want to reuse them with the RX100. Especially as the UFL165AD has incredible performance with stills and nothing can beat the flexibility of this lens and its very light weight in water let alone the speedy bayonet mount.
A final word about filters, in video filters are essential to restore colour however they also take away 1 1/2 f-stop of light so in low light the footage may get too grainy and it is actually better to work only with white balance.
I have heard many people commenting about the dreaded white balance error 9900K message of the RX100. So why is this happening?
It seems that the RX100 cannot white balance if the exposure is outside the -2 or +2 Ev range. If you do continue and ignore the error message you may end up with strange results.
So how to fix this? Contrary to what I said in my post about white balance I have worked out that it is best to set a custom white balance in P mode and not in M, this is because the camera will adjust exposure and never issue an error message. If you want to keep white balancing in M make sure you are within the allowed range of exposure.