All posts by interceptor121

SONY RX100, UNDERWATER VIDEO, White Balance

Sony RX100 – Tips for UW Video Part 3 Setting Custom White Balance

45 Comments

In this third post we will look at setting custom white balance in our RX100.

The ability to change the color temperature and adjust it to the conditions is essential to take underwater video as the ability to correct white balance in post processing is nowhere near what you can achieve with RAW files in photography.

Unfortunately the RX100 does not allow to set a custom white balance in video mode, and actually does not allow setting it in many other modes either. So to achieve our objective we will need to use the mode dial.

Note that the RX100 has the ability to store custom setting in 3 memory recall modes however in this mode the set custom white balance option is not available.

As we don’t have a one push option we need to minimize key presses to build a reliable routine that we can recall underwater.

If we have a look at the mode dial we see that the Manual mode for stills M is the closest to the video position so our routine will be based on switching between M and Movie mode. Update The new recommendation is to set the dial to P see note at bottom

Preparation is important and the RX100 has two options when it comes to recalling functions from the menu as we can see from this picture.

It is essential for our purposes that in this screen we select Previous, this will position us on the last entry we used when we click on the menu button again. The other option Top does not recall what the last entry was and puts you back on the top of the relevant menu, and would mean more navigation for us, so make sure you are set on Previous.

Another important trick to remember is that through the Function button we can recall the various white balance settings. In my set up white balance is right in the center of the function option so that when the function button is pressed we are immediately there should we need to change it back to Auto when we use lights, so when we plan to custom white balance this should be left on the Custom position as in the main picture of this post.

The other preparation that we need to do is to go in Manual Program mode and navigate until we reach the entry that allows us to set custom white balance as shown in the picture.

Note that from here we still have to actually select and go into another menu to then finally navigate to the bottom where the set custom wb option is.

We now want to re-balance either on slate or some grey area or sand so how do we do it?

The starting point will be in Movie mode with the White Balance set to Custom (remember this is not to set a new WB but just to recall the last white point set).

This is the step by step routine:

  1. Move the dial to position M P
  2. Press Menu – this will position us on the white balance entry in the menu
  3. Press Enter (central button) to access the options
  4. Scroll to Set Custom
  5. Press Enter
  6. Point at the slate and press the shutter
  7. Press Enter
  8. Turn mode dial to Movie – as we were set in function to Custom White point recall the setting we capture will be used

And we are done an 8 steps routine!

If you were used to a one push option this is a shocker!!!

For those on the more conventional option Menu-White Balance-Custom WB-Set-Menu this adds 3 more clicks.
Sony had made two very poor design decision for our underwater video purposes

  1. It has negated the option set custom white balance in video and now two turns of the Mode dial are necessary
  2. It has allowed to set a custom white balance only from the Menu but not from the White balance options that you can recall with the Function button, additional navigation is required because of this

I believe those issues can be fixed by a firmware update quite easily as they are clearly software issues the camera itself has got all the required capability.

That’s all for now if anybody has any alternative approaches that improve this routine I look forward to hearing what those are!

Meanwhile I recommend sending an email to Sony Support to ask for firmware changes…

Update 14 December 2012

Many people report a Custom WB error 9900K message. It turns out the RX100 fails to set custom white balance set up if the exposure is not within -2 to +2 range. So the new advice is to set custom white balance while in P mode

SONY RX100, UNDERWATER VIDEO

Sony RX100 – Tips for UW Video Part 2 – Rear Dial Buttons

7 Comments

In this second post we will look at how to set the rear dial buttons to best suit underwater video.

The RX100 has got a whole load of settings and not the most user friendly menu structure so it is important to have the features you need at your fingertips when the moment comes.

There are 3 essential features that a camera needs to have for underwater video:

  1. AF lock
  2. Exposure Lock
  3. Set custom white balance

Unfortunately as Backscatter noted in their review of the RX100 there is no possibility to set a custom white balance in any of the video modes, however in the next post I will guide you through the best available workaround that minimizes the chances of you getting completely lost in the menus…

It may be beneficial to understand first why those features are important so let’s have a look one by one.

AF Lock

Have you ever experienced being in a school of fish? Or looking at some frantic behavior in front of you or simply seeing glassfish swarming in front of your camera lens?

It will look something like this…

This is not a still picture but a snapshot of a clip taken at 1/125 sec shutter speed, the action was actually fairly fast.

This is the clip if you want to check it out,

this scene is in the first part of the movie and  has been shot with AF Lock on a Sanyo Xacti HD2000.

What would have happened without AF Lock? The camera would have been looking for focus and mistaking some of the fish coming close with the actual subject and as result the clip would have been unwatchable. So this makes focus lock very important for us in all situation where we operate in tripod mode with moving fish in front of the lens.

The RX100 does not offer AF Lock with a single push, and in video mode the choice is between tracking auto focus and manual focus. To emulate the AF Lock feature I follow this procedure:

  1. Track my focus point with tracking AF
  2. Switch to Manual Focus

Note that is not possible to simply cancel tracking AF to obtain AF lock as the contrast detection system will still wonder around the center of the frame.

This means that one of the rear dial buttons accessible in the menu settings 2 should be set to AF/MF Control Toggle that will allow us to quickly operate the steps above and move with one click from tracking AF into manual and effective locked focus.

Exposure Compensation

Another essential feature of video as we don’t want the camera to continuously adapt to the changing light conditions of the scene. To give an example let’s have a look at this picture:

This is a swim-through that is a common features of little caves or even wrecks. We don’t want the camera to compensate for the lack of light whilst we go through as that would increase the ISO and make the footage grainy, also the scene would get brighter and not reflect to the viewer the same experience we had.

Exposure lock avoids this situation so when we are at the beginning of the cave we lock exposure and the scene stays dark so that the end of the swim through gives a beautiful effect. Another example with this technique

So we should reserve another of the rear dial buttons to Exposure lock that on the menu system is called AEL Toggle

This is how my rear dial configuration looks in the Setting menu 2

Note that I left the center button to standard as that corresponds to tracking focus. That is required for the pseudo AF lock in conjunction with the Right button as discussed earlier in this post.

SONY RX100, UNDERWATER VIDEO

Sony RX100 – Tips for UW Video Part 1- File Formats

8 Comments

When the new SONY DSC-RX100 was released early June many people were really excited as this camera featured a 1″ sensor at its heart.

Scott at Underwater Photography guide posted a raving review from which I was left salivating

Later on backscatter selected the RX100 as the best advanced camera of the year read more here however one statement left me concerned in the Pro and Cons section: No way to execute custom white balance in movie mode, must jump to photo mode

This sounded quite uneventful considering that we are almost used to one push custom white balance on most mid level compacts.

Maybe those guys looked at the Sony entirely from a still perspective and did not make much of the features or lack of thereof that this Sony has, anyway I have now bought the camera itself and I am facing a few issues and dilemmas.

Let’s take a close look at those one by one and start this issue with…

FILE FORMATS FOR VIDEO

SONY has decided to adopt the new high specs AVCHD formats for this camera, I will from now on refer to 50p or 50i to indicate 50 progressive or 50 interlaced frames as this is the PAL standard. This would be 60p or 60i for NTSC US and Japanese users.

The AVCHD format had initially a 1080/50i and a 1080/24p format and a bunch of lower resolution formats, later on a 1080/50p format has been added with an increased bit-rate of 28 Mbps instead of the original 24.

Now you would normally assume that Sony would have chosen to support all those formats and instead has decided just for the 1080/50i and 1080/50p. The universal 1080/24p format that is compatible with both PAL and NTSC is not supported on the RX100. Why has Sony made this decision is a mystery.

The make things worse today interlaced display do not exist anymore and most of the non linear video editor convert interlaced footage in progressive otherwise you can’t actually edit the clips. Not only that very few software programs actually accept the new 1080/50p format, with the notable exception of Sony software that even at low level supports those formats. Adobe premier is another one, but the whole set of Apple software including iMovie and Final Cut Pro don’t know what to do with those files. Let alone the fact that no devices except powerful computers can actually play those files well.

The RX100 offers an MP4 format at 1440×1080 rectangular pixels with a 16:9 aspect ratio as a reminiscence of HDV. This format is however easily digestible by the majority of NLE on the market. So we would feel rather tempted to use it.

The question is how do we set our RX100 to capture underwater video?

The answer is actually at the highest possible setting that is 1080/50p. There are several reasons for this.

  1. The human eye is very sensitive to resolution. So the MP4 1440×1080 format goes out of the window
  2. We can still change the frame rate in editing phase to make the file a more normal 1080/25p
  3. There is not a huge difference in memory card use between the 24 Mbps of the highest interlaced mode and the 1080/50p
  4. It is easier to edit progressive frames without conversion
  5. Progressive footage does not introduce artifacts as  interlaced does

On a negative note the fact that we are saving AVCHD streams means goodbye back ups on our tablets or mobiles so plenty of memory cards with us during our trips.

The next challenge will be to import the AVCHD streams into our movie editor. As mentioned earlier the 1080/50p format is not recognized by many entry level programs so some will not even see those files.

Other programs will try and convert it, this option has to be disabled and the files imported as they are without any changes to preserve quality.

So what do we do if our software refuses to process the 1080/50p files in our AVCHD streams?

A number of help tools come handy unfortunately the freeware one are mostly on windows and I have not managed to produce anything that works yet with Wine for Mac. On Mac there are two tools iVI that costs $9.99 and ClipWrap more expensive both functional and will produce an M4V or MOV that can be processed with iMovie or other tools that would have previously rejected the file you go figure!!!